Mechanical Characterization of Armchair and Zigzag Single-walled Carbon Nanotube

Authors

  • R. Hamood
    Department of Physics, Faculty of Education/Saber, University of Aden, Yemen
  • Samia Jamal
    Department of Physics, Faculty of Education/Saber, University of Aden, Yemen
  • Zina A. Al Shadid
    Department of Physics, Faculty of Education/Aden, University of Aden, Yemen

Keywords:

Single walled Carbon nanotubes, Mechanical properties, Finite element analysis, Young’s modulus

Abstract

The stress-strain and Young’s modulus values of single-walled carbon nanotubes SWCNTs are modeled through linear finite element simulations and Matlab codes, in this study. Cylindrical zigzag and armchair single-walled are established as carbon nanostructures. An individual carbon nanotube (CNT) is simulated as a frame-like structure and the primary bonds between two nearest-neighboring carbon atoms are treated as 3D beam elements. The stiffness and the stress-strain curved of the SWCNTs are investigated. The effect domination of the nanotube diameter of the CNTs on Young’s modulus is studied. The simulation results acquired in this study are in good agreement with the experimental results. 

Dimensions

P. M. Alderton, J. Gross & M. D. Green, “Comparative study of doxorubicin, mitoxantrone, and epirubicin in combination with ICRF-187 (ADR-529) in a chronic cardiotoxicity animal model”, Cancer Res. 52 (1992) 194, http://aacrjournals.org/cancerres/articlepdf/52/1/194/2446804/cr0520010194.

D. Tasis, N. Tagmatarchis, A. Bianco & M. Prato, “Chemistry of carbon nanotubes”, Chem. Rev. 1063 (2006) 1105, https://pubs.acs.org/doi/10.1021/cr050569o.

S. N. Kim, J. F. Rusling & F. Papadimitrakopoulos, “Carbon nanotubes for electronic and electrochemical detection of biomolecules”, Adv. Mater. 19 (2007) 3214, https://doi.org/10.1002/adma.200700665.

Y. Zhang, Y. Bai & B. Yan, “Functionalized carbon nanotubes for potential medicinal applications” Drug discovery today 15 (2010) 428, https://doi.org/10.1016/j.drudis.2010.04.005.

L. Luer, S. Hoseinkhani, D. Polli, J. Crochet, J. Hertel & G. Lanzani, “Size and mobility of excitons (6,5) carbon nanotubes” Nat. Phys. 5 (2009) 54, https://doi.org/10.1038/nphys1149.

Y. Usui, H. Haniu, S. Tsuruoka & N. Saito, “Carbon nanotubes innovate on medical technology” Medicinal Chemistry 2 (2012) 1, https://doi.org/10.4172/2161-0444.1000105.

R. Rafiee & R. M. Moghadam, “On the modelng of carbon nanotubes: a critical review”, Compos. Part B 56 (2014) 435, https://doi.org/10.1016/j.compositesb.2013.08.037.

J. L. Tsai & J. F. Tu, “Characterizing mechanical properties of graphite using molecular dynamics simulation”, Materials & Design 31 (2010) 194, http://dx.doi.org/10.1016/j.matdes.2009.06.032.

K. Lau, C. Gu & D. Hui, “A critical review on nanotube, /nanoclay related polymer composite materials”, Compos. Part B Eng. 37 (2006) 425, https://doi.org/10.1016/j.compositesb.2006.02.020.

E. T. Thostensona, Z. Renb & T. W. Choua, “Advances in the science and technology of carbon nanotubes and their composites a review”, Compos. Sci. Technol. 61 (2001) 1899, https://doi.org/10.1016/S0266-3538(01)00094-X.

G. M. Odegarda, T. S. Gates, L. M. Nicholsonc & K. E. Wise, “Equivalent –continuum modeling of nano-structured materials”, Composites Sci. and Techno. 62 (2002) 1869, https://doi.org/10.1016/S0266-3538(02)00113-6.

N. Khandoker, S. Islam & Y. S. Hiung, “Finite element simulation of mechanical properties of graphene sheets”, IOP Conf. Series: Materials Science and Engineering 206 (2017) 012057, https://doi.org/10.1088/1757-899X/206/1/012057.

C. Baykasoglul & A. Mugan, “Failure analysis of graphene sheets with multiple stone-thrower-wales defects using molecular-mechanics based nonlinear finite element models”, Hittite Journal of Science and Engineering 5 (2018) 19, https://doi.org/10.17350/HJSE19030000073.

X. L. Li & J. G. Guo, “Theoretical Investigation on failure strength and fracture toughness of precracked single-Layer graphene sheets”, Hindawi Journal of Nanomaterials (2019) 1, https://doi.org/10.1155/2019/9734807.

P. Papanikos, D. D. Nikolopoulos & K. I. Tserpes, “Equivalent beams for carbon nanotubes” Comput Mater Sci 43 (2008) 345, https://doi.org/10.1016/j.commatsci.2007.12.010.

Q. Lu, W. Gao&R.Huang,“Atomistic simulation and continuum modeling of graphene nanoribbons under uniaxial tension”, Modelling and Simul. Mater. Sci. Eng. 19 (2011) 1, https://doi.org/10.1088/0965-0393/19/5/054006.

Q. Lu & R. Huang, “Excess energy and deformation along free edges of graphene nanoribbons”, Phys. Rev. B 81 (2010) 1, https://doi.org/10.1103/PhysRevB.81.155410.

E. G¨unay, “Modelling of single walled carbon nanotube cylindrical structures with finite element method simulations”, AIP Conference Proceedings 1727 (2016) 020009-1, https://doi.org/10.1063/1.4945964.

T. W. Chou & C. A. Li, “Structural mechanics approach for the analysis of carbon Nanotubes”, Int. J. Solids Struct. 40 (2003) 2487, https://doi.org/10.1007/s11012-009-9222-2.

Published

2022-04-29

How to Cite

Mechanical Characterization of Armchair and Zigzag Single-walled Carbon Nanotube. (2022). African Scientific Reports, 1(1), 23-31. https://doi.org/10.46481/asr.2022.1.1.19

Issue

Volume 1, Issue 1, April 2022

Section

Original Research
Copyright & Licensing

Copyright (c) 2022 R. Hamood, Samia Jamal, Zina A. Al Shadid

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

Mechanical Characterization of Armchair and Zigzag Single-walled Carbon Nanotube. (2022). African Scientific Reports, 1(1), 23-31. https://doi.org/10.46481/asr.2022.1.1.19

Similar Articles

71-80 of 98

You may also start an advanced similarity search for this article.